紙箱企業在檢驗邊壓強度時不選用導塊支撐試樣,
Carton enterprises do not use guide blocks to support samples when inspecting the edge pressing strength,
簡略構成試樣不才壓過程中出現傾斜現象,數據偏低。
The sample with simple composition is inclined during the pressing process, and the data is low.
正確的方法是將試樣置于實驗儀下壓板正中間,用導塊支撐試樣,
The correct method is to place the sample in the middle of the lower pressing plate of the tester and support the sample with a guide block,
紙箱定制
Carton customization
使試樣的表面垂直于壓板,當加壓靠近50N時移勸導塊,直至試樣壓潰,記載試樣所能承受的壓力。
Make the surface of the sample perpendicular to the pressing plate. When the pressure is close to 50N, move the persuasion block until the sample is crushed, and record the pressure that the sample can withstand.
紙箱
carton
點破強度的試樣要分別檢驗正面縱向、不好縱向、正面橫向、和不好橫向四個不同角度值,而部分企業在檢測時卻不考慮試樣檢測時的角度。其實在實踐檢測時,正面縱向、不好縱向、正面橫向、和不好橫向四個不同角度的檢驗效果有時相差較大。
For the sample with puncture strength, four different angle values of front longitudinal, bad longitudinal, front transverse and bad transverse shall be tested respectively, but some enterprises do not consider the angle of sample testing. In fact, in practical inspection, the inspection effects of four different angles: positive vertical, bad vertical, positive horizontal and bad horizontal sometimes differ greatly.

耐破強度檢測時,對出現二次爆炸聲的數據或當試樣有明顯滑動時應將數據拋棄,并且要分別測定樣品的正、反雙面。一般情況下,在進行檢測時出現比較失常的檢驗數據應該增加檢驗次數來驗證檢驗效果是否歸于偶然現象,以避免構成差錯判定。
During the burst strength test, the data with secondary explosion sound or when the sample has obvious sliding shall be discarded, and the front and back sides of the sample shall be measured respectively. In general, for abnormal inspection data during inspection, the inspection times should be increased to verify whether the inspection effect is accidental, so as to avoid constituting error judgment.
對紙箱抗壓強度檢測時不封箱就進行檢驗,這樣會構成檢測數據偏低。正確的方法應該首先將樣箱立體合好,用封箱膠帶上、下封牢,然后放入抗壓實驗機下壓板的中間方位,標準速度加壓,直至將紙箱壓潰。
When testing the compressive strength of the carton, the carton is tested without sealing, which will constitute that the test data is low. The correct method should first close the sample box in three dimensions, seal it up and down with sealing tape, and then put it in the middle of the lower pressing plate of the compression testing machine, and pressurize it at the standard speed until the carton is crushed.
一般顧客在收貨時選用游標卡尺或直接用卷尺直接測定紙板的縱切邊,來判定紙板的厚度。由于紙板出產線在縱切時,薄刀縱切有必定的壓力,紙板的縱切邊一般會有壓塌,這樣測守時數值會偏低。其實在進行厚度測守時是在必定壓力下測定的,并且要選擇多點接觸測定取平均值。
General customers choose vernier caliper or directly measure the longitudinal cutting edge of paperboard with tape measure to determine the thickness of paperboard. Because there is a certain pressure in the slitting of the paperboard production line, the slitting edge of the paperboard will generally collapse, so the punctuality value will be low. In fact, the thickness measurement punctuality is measured under a certain pressure, and multi-point contact measurement should be selected to take the average value.
The wonderful contents of this article are provided by the knowledge of Jinan packing factory. There are many wonderful contents on this website. You can click to enter more contents: http://www.m8457.cn We have special customer service to answer your questions